メインコンテンツへスキップ
見出し画像

The Ultimate V-Sleep Manual: the VR sleeping setup on Quest 3 that lets me sleep every day

    ==============================================
    Note: As an Amazon Associate I earn from qualifying purchases.
    ==============================================

    Good morning (at noon).

    It’s been a month and a half since I started VRChat. I’ve gotten hooked on V-sleep—aka VR sleeping—which I used to dismiss with “who would go out of their way to do that?”

    Needless to say, VR sleeping is the cutting-edge oddity of our times where you deliberately lie down with your VR headset on and go to sleep inside a VRChat world online.

    おはようございます(昼)
    昨日の #Bar_ZuLu のアフターは鍋パワールド。完全に宅飲み気分で、目が覚めたら空き缶と床で寝てるところまで完全再現…。
    書き置きありがとうございました。 pic.twitter.com/YxBnqVFkuq

    — ハルジオン (@fleabane_haru) November 11, 2023

    I often hear that people do V-sleep because it’s calming to sleep together with others. That said, as the saying goes, “your MP recovers but your HP doesn’t,” so a lot of folks know they’d probably be better off just sleeping normally.
    (Which is only natural, since you’re wearing a headset that’s obviously in the way.)

    That said, I feel I sleep better with V-sleep than sleeping the regular way. Of course the headset is intrusive, but I fall asleep faster than that downside matters.
    It used to often take me over an hour from getting in bed to actually falling asleep, but with V-sleep I crash in 10–15 minutes. I’ve observed a few friends in similar situations, and some friends say their insomnia has improved.
    Not doom-scrolling on my phone or YouTube helps, but so does chatting with people and getting into bed relaxed; plus the chill vibe and dim lighting of sleep worlds and the understated BGM all tell every sense to “sleep.”

    You might think, “But isn’t that light sleep?”—however, according to my smartwatch it’s solid. I’m out cold until the alarm goes off.
    My deep sleep is generally over the one-hour rough benchmark, and I wake up feeling no different from a normal night.
    So of course I’m going to V-sleep.

    今日もよく寝た。案外快適じゃないか。 pic.twitter.com/HiH8haRdYn

    — ハルジオン (@fleabane_haru) October 31, 2023

    That said, I can’t recommend it to complete beginners. There are definitely environments and gear that suit it and those that don’t, and in an unsuitable setup it will absolutely tire you out.
    Which is why, for eccentric friends attempting the same thing, I’m going to share the well-rested setup I’ve built over 2,000 hours of V-sleep.


    ① Headset (Hardware)

    Needless to say, this is the most important part. I’m a heavy user of the Meta Quest 3. This thing is quite suited for V-sleep.

    Above all, what matters is weight. When you lie on your back, the weight lands squarely on your cheekbones and forehead, so a 100 g difference feels like a different device. The Quest 3 is 500 g—neither especially heavy nor light—but compared to a 700 g+ Vive Pro or Valve Index, the difference is night and day. Honestly, though, even lighter would be preferable.
    The center of gravity (how far it sits from your face) is also a big factor. When you sleep you loosen the headstrap, so if you lightly roll over and your face turns sideways, a far-forward center of gravity creates torque that makes the HMD shift, which is uncomfortable. Thanks to its pancake lenses, the Quest 3 has a thin front end, and this is comfortable. You’ll really feel it if you try against a Quest 2 or 3S.

    I also think inside-out tracking (no base stations needed) matters. When sleeping, you want to minimize mental overhead, so you don’t want the stress of tracking dropping out depending on your rolling over or where the blankets are.
    Another point is that it’s (relatively) inexpensive. …As some enthusiasts jokingly call it a “luxury sleep mask,” $500 is indeed pricey, but compared to HMDs north of $1,000 it feels much more reasonable.

    画像
    (paid link below)

    That said, even the Quest 3 has pain points when stock. So I did four simple mods: (1) charging connector, (2) lenses, (3) ocular interface cover, and (4) straps.

    (1) The Quest 3’s cable plugs in from the side, so if you roll over to the left as-is, you’ll break it. Use an L-shaped adapter like this to route the cable rearwards. If there’s a pillow under you, this is enough.

    画像
    (paid link below)
    画像
    L-shaped connector + how to route the charging cable. If you loop it inside the headstrap, you’re less likely to stress the connector.
    画像
    How it looks when side-sleeping. Surprisingly the connector doesn’t take much load, so you can roll over (no failures after 1+ year of use).


    (2) I can’t live without glasses, so I installed prescription lens inserts for the Quest 3. I don’t want to wear glasses inside an HMD—nor sleep with glasses on. You can scratch the lenses if you’re unlucky. In that regard, it’s great that the Quest has robust first-party and third-party options.

    (paid link)

    (You can usually get your sphere/cylinder (CYL)/axis (AXIS) values by asking the shop that made your glasses.)

    (3) For the ocular interface cover, I use VRCover. Compared to the stock cushion, it distributes contact pressure better, and the hand-feel and breathability are improved, making it comfier to sleep.

    画像
    (paid link below)

    Since I wear this every day to sleep, I was concerned about sweat and skin oils. Being able to remove and wash the cover was the deciding factor.
    VRCover costs $34—about the same as a full face-cushion kit on the pricier side—but it includes two sets from the start, so it’s nice to swap and use them freely. This part touches your skin directly and affects sleep comfort directly, so it’s worth caring about.

    I also bought AMVR’s face cushion and now use it alongside VR COVER. In addition to the venting that reduces heat buildup and fogging, the height adjustment is a big deal. In particular, you can adjust the forehead side and cheekbone side independently, so if only your forehead is taking pressure—or the reverse—this will really fit you.

    画像
    (paid link below)

    Also, in summer the ocular interface does get stuffy and a bit itchy. For those concerned, I recommend disposable face masks for VR. It reduces stuffiness and prevents rubbing, making them suitable for sensitive skin. The nose section is annoying, so cut just that part with scissors or fold it in two—works nicely. Also recommended if you think VRCOVER is a bit pricey or washing is a hassle.

    (paid link)

    (4) Lastly, straps. The flimsy stock headband is surprisingly easy to sleep with, but for day-to-day comfort I want an Elite Strap. However, that’s a pain when sleeping, and swapping every time is a hassle.
    My solution was to combine two straps. This was the most trial-and-error, so please use it as a reference.

    One is a flip-up style hard strap. The other is a soft headband.

    画像

    When I’m upright or playing high-motion games, I mainly use the hard strap as in the photo above. Great hold.
    When I lie down—i.e., for sleep—I move the annoying thing at the back of my head, the hard strap, up toward the crown. In its place, the soft headband gently maintains retention, as in the photo below.

    画像

    This way, only the soft band touches the back of the head, so it’s extremely comfortable for lounging naps. The hold isn’t that tight, but that means it’s less tiring, and for sleep it’s enough. The biggest benefit is being able to roll freely. It removes a major cause of fatigue in V-sleep, so it’s very comfortable.

    画像

    If you route the cable through the loop of the cord, it won’t flail.
    For fastening the headband, connecting cords for craft is just right like below (paid link). The narrow cord portion bites into the hinge area of the headstrap. Use zip ties together. 

    About headstrap, I use YipuVR one, but it's not available in US so I recommend instead this strap below (paid link):

    画像

    The point is wide angle of movement. That's definitely important.
    For soft headband, after trying various headbands, this Nike kids’ headband below (paid link) had the best sizing. The cotton fabric feels good and is breathable. If it's tight, use zip ties to adjust.

    画像

    This is a V-sleep MOD you can do easily for under $50, so definitely give it a try. It absolutely raises your QOL. …Well, it just gets you a bit closer to a normal sleeping state. V-sleep is a deep rabbit hole.

    By the way, here’s an article showing a similar custom using the well-reviewed BOBOVR headstrap; if you’re a BOBOVR user, use it as a reference.

    Now, a subtle pain point in V-sleep is charging. Depending on charger compatibility, the Quest 3 sometimes can’t keep up on power, and even when plugged in the battery can drop and the HMD can die mid-sleep.
    To avoid this, the prerequisite is a USB-C-to-C cable. A Type-A-to-C tops out at 10 W and isn’t enough, so you need a USB-C cable that supports Power Delivery (PD). Length-wise, even if you run it from the bedside you want at least 2 m, ideally 3 m. Softer cables are better.
    Also, on the power source side, you need PD support and around 30 W of output to cover losses. Rather than over-explaining, I’ll just list the gear that has worked fine for me.

    (paid link)

    Note that in V-sleep the most failure-prone part is the cable. When you roll over, the cable can bend sharply or get pinched, leading to breaks or bent connectors.
    This is one reason I recommend going wireless: DP-tethered PCVR or the Quest 3’s wired Link uses relatively thick cables for both data and power, and these are susceptible to bending damage. In particular, the 5 m Meta Quest Link cable (around $80) is fiber-optic and especially prone to breaking. On the Vive and Bigscreen Beyond as well, damage near the HMD-side connector is a common fault—and those proprietary cables aren’t cheap.
    Of course, even if you go wireless you still need a power cable, but power-only cables are thinner, more flexible, and less likely to break; and even if they do, they’re cheap and easy to source. This kind of failure risk is another reason why going wireless on Quest 3 for sleeping is my top recommendation.

    ====================================
    Refer to the older version of the strap MOD below.
    ====================================

    How-to: Fix a slim sports headband to the Quest and route it around the back of your head. The hold is weak, but for just sleeping it’s sufficient.

    (paid link)

    画像
    It looks like this when sleeping.
    画像
    Fix the headband to the base of the top strap.


    ①' Headset (Can we make it lighter?)

    Now then: when a headset is heavy, you have to cinch it down firmly. That worsens comfort due to clamping and heat buildup. In other words, the biggest optimization for comfort is weight reduction.
    But modding electronics to physically make them lighter is unrealistic … so here I’ll introduce a ridiculous brute-force lightening hack.

    Hang it from above.

    画像
    LoL

    The Quest 3’s drawback is being front-heavy, but it helps, simply hoisting the unit takes a dramatic load off how it feels to wear. What you use is a ceiling bungee/reel set meant for suspending VR cables (paid link below).

    画像

    If you lift with two reels, a Quest 3 that actually weighs 600 g feels like 200 g. That’s a straight-up revolution.
    On the Quest 3 side, use the top strap’s stock belt loop as the anchor. The KIWI design reel’s belt fits right through here. However, since removing it is a hassle for me, I thread a hook-and-loop strap and clip on a carabiner.

    画像
    paid link below

    The biggest problem is where to hook these reels in your room. To keep the reel action light and avoid being pulled at weird angles, it’s ideal to have the reel directly above your home position as much as possible.
    Ideally, install a tension rod or rail on the ceiling along the front-back axis. Hang from that. It moves the smoothest.

    画像
    Suspending the headset from a tension rod.

    If it’s by a window, you can zip-tie an angle bar to the curtain rail like this, then hang the reel from an S-hook on the end. Please experiment to suit your living environment.

    画像

    Also, once you’re lightening the load from above, you can go with a much looser (= comfier) headband. This is what I use. If the length is borderline, add some zip ties as spacers and fine-tune the clamp—OK.

    Setup is a hassle, but the effect is immense. A headset you used to clamp tightly to keep from slipping will remain stable even with the headstrap loosened to floppy. That eliminates clamp fatigue and heat buildup, making it wonderfully comfortable. You can wear it all day.

    You may think, “No, it’s definitely in the way…”—but I’ve already lived with this for over a year and it’s extremely comfortable. I sleep deeply with V-sleep in this setup at night, too. Especially if you barely move from your chair or bed, try it—you can thank me later.

    That said, this is a relatively high-bar MOD, so only try it if you really want to reduce the perceived weight. In fact, I slept about a year without this.


    ② Headset (Usage)

    There are various key points in the Quest 3’s settings as well.

    First, in Settings > Power, set the Display Off and Sleep Mode timeouts to 4 hours. If these are short, the Quest 3 may power down while you’re V-sleeping, and depending on your connection method VRChat may also close, which would be sad—so watch out.

    画像

    Next, make going wireless a top priority. Even the charging cable alone is a hassle; if you have multiple bulky cables sprouting out, there’s no way you can sleep. There’s also the cable breakage risk I mentioned earlier. I recommend going wireless with Guy Godin's Virtual Desktop, the de facto standard for both features and stability. It’s also nice that even if a cable comes loose or you run out of battery, VRChat doesn’t crash (you can reconnect and resume).

    Next, lower the headset’s brightness. Dimming a world’s lighting is important too, but if the display is bright, it’s still hard to sleep. On Quest-series headsets you can adjust brightness from the bottom-left quick menu (you can also do this later via OyasumiVR). While you’re at it, tweak the volume as well.

    画像
    Bottom-left quick menu ⇒ adjust from the brightness control at the top right.

    Also set the controllers aside. After all, Quest has hand tracking. In VRChat you can’t locomote with it, but your hands do move, so you can wave to people or check the time with XSOverlay. Just place the controllers down, or turn on gesture control, or power them off, and you’re good. I use Quest Pro controllers, so I return them to the charging dock—no battery anxiety; two birds with one stone.


    ③ Bedding

    It’s sleep we’re talking about, so this is obviously the most important part. In fact, regardless of V-sleep, everyone should use good bedding.
    What’s the idea of bragging “a VR HMD is bedding” and dropping $1,000, while your actual pillow and mattress are cheap?

    Pillows vary by person, but as a general rule for V-sleep—where the headset sits on your face—a pillow with neck and shoulder  support is likely better suited.

    画像
    paid link below

    There are hacks like using a donut pillow or bead cushion to make room for the rear headstrap, but in my setup the back is only a headband, so my pillow options are broader—and the comfort is obviously better, too.

    Also, for those using models like Pico or Vive where, as explained in ①, you can’t swap straps: I’ve reviewed V-sleep pillows suited to such HMDs—ぶいすいーと スイフト and the side-sleeping ぶいすいーと Your Side—in a separate article, so please give it a read.

    And you should definitely buy a body pillow.
    With one, when you lie on your side, you can rest the headset’s weight on it. The HMD won’t shift, and unlike when you’re supine, the weight won’t press on your face. It’s comfy.

    画像
    paid link below
    画像
    paid link below

    A standard body pillow like this is fine, but my personal, serious recommendation is this Livheart body pillow, Shiba Inu Kotarō. The nose is at just the right height to rest the Quest’s weight while sleeping. And the hand-feel and hug feel are insanely good. It’s perfection when you’re co-sleeping with someone.

    Good bedding never goes to waste, so before you buy VIVE Trackers, please get a good pillow and a body pillow first.


    ④ Software (Mastery & Workflow)

    For sleeping, I don’t recommend full-body tracking (FBT). Of course there are individual differences, and there are a fair number of people who sleep with it. But even HaritoraX Wireless is intrusive for me and keeps me from sleeping soundly; and VIVE Trackers are a no-go because they’re bigger and heavier, tracking drops more easily, and you can’t really use blankets with them.
    Therefore, I recommend a method based on inside-out 3-point tracking and adding sleep gimmicks to your avatar.

    Recommended pick by use case:

    Naturally, I use “the best.” RBS lets you roll over in response to posture, so your sleeping pose looks natural, and it works even where there are no colliders. It’s also announced as compatible for concurrent use with Kawaii Pose Tool, which lets you take a variety of poses, and both support Modular Avatar, so installation is simple. This combo has no weaknesses.

    Adjustment is fiddly, but you’ll get used to it after a few tries. OVR Advanced Settings makes fine-tuning easy, so I recommend it.

    So, in the end, the only thing I wear when I sleep is the headset. Relaxing.

    画像

    Also—depending on the avatar—it’s nice to have a gimmick that locks facial expression and lets you close your eyes. When the eyes are wide open, it’s unsettling for people nearby.
    Don’t dismiss it as “just a sleeping pose.” In a space where the V-sleep “vibe” is what creates drowsiness, the appearance matters quite a bit. Especially if you’re sleeping with someone, looking like you’re peacefully dozing makes it more pleasant for the viewer too.

    画像
    Suyasuya

    Once your sleeping posture looks clean, I strongly recommend seeing yourself in a mirror. VR is close to hypnosis, so when you see yourself sleeping it makes you naturally get sleepy.
    If the world has a bed mirror, use it actively; if not, the standard VRChat Personal Mirror works fine. You’ll be suyasuya anywhere.


    And, beyond avatar gimmicks, a tool you must install is OyasumiVR.

    It detects sleep onset and automatically changes various settings; it’s packed with V-sleep features like auto-muting the mic, auto-approving Request Invites, and display brightness control. You can also launch it as an overlay from within VRChat, which is convenient.
    A recommended feature is PC power (energy-saving) control. You can cut V-sleep electricity costs by about 30%. For the power-saving settings and their effects, see this article.

    Among OyasumiVR’s features, the one that’s especially crucial for good sleep is lowering screen brightness.
    One cause of poor sleep quality in VR sleeping is that the display is bright. Dimming it properly at bedtime matters more than you think; if you wake up mid-sleep, getting back to sleep is harder when it’s bright. Especially on Quest and Pico (LCD panels), the screen tends to be bright. Use this feature for better rest—no excuses.

    Items you should configure: first, set it to auto-launch with SteamVR. In SteamVR > Settings, enable it under “Startup Overlay Apps.”
    To open the overlay in VRChat, press the Jump button twice. You can manually toggle Sleep Mode ON and adjust screen brightness.

    画像

    Next, in Brightness Automation, set During Sleep: 40% / Upon Wake: 100%. When sleep-onset is detected or you manually turn Sleep Mode ON, it will automatically dim. You can nod off without worry.

    画像
    Brightness automation settings

    Another useful one: set a scheduled disable time so that when morning comes, the brightness rises as if sunlight were coming in, helping you wake naturally. Set it about 15 minutes before your alarm.

    画像

    There are many other settings, so please explore and find your best sleep configuration.


    ⑤ Miscellaneous

    As a fundamental premise, even with V-sleep, sleep in a proper bed. This is the most important point. Most of the reasons V-sleep feels tiring are because you’re not sleeping in a bed. Dont't sleep on chair.

    If you go wireless with something like Virtual Desktop (VD), it’s not that hard to sleep away from your PC. So if V-sleep “doesn’t work for you,” first build a setup that lets you sleep in bed. For reference, my PC room and bedroom are a bit apart, but I ran wired LAN from the PC to the bedroom, placed a Wi-Fi access point there, and connect VD to that (paid link below).
    (The closer the radio point, the more stable the connection. If your VD is laggy or looks bad, it’s often a networking issue.)

    Virtual Desktop+Quest3で、PCから離れた寝室でVRができる環境を整えてみた。

    (書斎PC)-有線LAN-(寝室アクセスポイント)-WiFi-Quest3

    Min72~90fps出てレイテンシも50msくらい。音響周り以外書斎のPC前と遜色ない。完璧。 pic.twitter.com/naSspn3mhQ

    — ハルジオン (@fleabane_haru) October 29, 2023

    While I personally recommend preparing an environment where you can sleep in bed for V-sleep, if your HMD is wired-only, or you “only V-sleep once in a while,” another option is to set up a folding bed near the PC.

    画像

    Also, obviously it’s easier to sleep if the room is properly dark, so install an IR illuminator in the room so inside-out tracking doesn’t drop even in the dark.

    アクセスポイントはTP-linkのRE605。Wi-Fi6E対応で1200Mbps出て6000円ちょい。
    部屋が暗くてもトラッキングが飛ばないよう赤外線ライトも据え付けた。LANケーブル入れても1万円程。

    (2枚目はQuest3のパススルーで撮影。ライトが光ってるのが分かる) pic.twitter.com/9SdwxJFvjY

    — ハルジオン (@fleabane_haru) October 29, 2023

    I use this IR light (paid link below).

    画像

    After trial and error with placement for this IR light, the conclusion is that placing it outside your field of view yields the best tracking accuracy. Relative to the direction you usually face when wearing the HMD, behind + above is best.
    (We tested three patterns for the light position in the diagram: ① in front (in view), ② to the side (in view), ③ behind (out of view). The best tracking accuracy was the one on the right, pattern ③.)

    画像

    (HMDs like the Quest “see” the surroundings in infrared to determine motion. So even in darkness, if there’s IR, they can track. But just like a human eye gets dazzled by looking straight at a bulb, if the HMD looks directly at the IR light, it actually makes it harder to see the surroundings. That’s the logic.)

    Depending on your room layout, mounting to a curtain rail is very convenient. Hooking it to the wall with thumbtacks also works.
    If tracking is unstable, sometimes plain or strongly patterned wallpaper/curtains confuse the camera-based tracking. Hanging a landmark—like a poster or T-shirt—on the wall can improve stability (it fixed instability I had with my Quest Touch Pro controller tracking).

    Also, what bothers you in summer V-sleep is heat and humidity—after all, a heat source is sitting on your head…
    Of course you should run the AC, but I also recommend a small USB fan. Place it above your head when lying supine, with airflow just skimming past the headset, and it will carry away heat and moisture nicely. Avoid direct wind on skin for health/comfort. With this, you don’t need to refrigerate the whole room.

    (paid link)


    Summary

    A grand title like “Ultimate V-Sleep Manual,” but in a word: sleep in a proper bed. Darken the display and the room. Remove whatever you can remove. And buy good bedding.
    If you say, “Then take off that weird thing on your head first,” you’re absolutely right—but let’s pretend we didn’t hear that.

    Overall, I still think the Quest 3 is well-suited to V-sleep.
    Inside-out tracking keeps hassle low; it’s relatively light and compact; passthrough, hand tracking, and the UX around the menus are solid. You can go wireless with VD, and the consumable cables are cheap. Above all, it’s a mainstream device, so aftermarket parts like headstraps abound.
    If you wanted something “better,” it would be VIVE Focus Vision, MeganeX SL 8K, or Bigscreen Beyond, but the first is heavy, and the latter two need base stations for the controllers. Plus, all of them cost well over twice the ~¥80,000 Quest 3.
    Even if told to choose with an unlimited budget, I’d probably still land on the Quest 3.

    画像
    (paid link below)

    Just a final note.
    It’s better to sleep normally than to sleep in VR. I’m only fine because I’ve tuned the environment; sleeping with an HMD is a debuff by default. If your environment isn’t comfortable, keep the frequency moderate or it’ll be hard on your body. Same category as alcohol or tobacco.

    That said, there’s the fun of this techno-eccentricity, the warmth from a friend’s “good morning” note, and the happiness of having someone there when you wake up. If you’re the kind of person who sleeps better on trips than at home, this might be worth trying.

    Use as directed and enjoy your V-sleep life.

    That’s all!

    画像

    X(Twitter)
    https://twitter.com/fleabane_haru

     
     
    VRChatでよく寝てる人です。VR機器チョットワカル。 お仕事のご相談はX (Twitter)のDMまたはnoteのページ最下部「クリエイターへのお問い合わせ」まで。 VRChatID: ハルジオンf

    あなたへのおすすめ