
Live告知と遠隔でバンドの同期演奏を実現する話#1──SYNCROOM×Logic Pro 格闘記
【Information】
東京・関西・ロサンゼルスのメンバーで構成される遠隔バンド「MELONARRATE」、初のリアルライブの詳細が決定しました。
公演日:2026年10月10日(土)開場 16:30 / 開演 17:00
場所:新宿LiveFreak
MELONARRATE 出演時間:19:50〜
チケット料金:前売 ¥2,000(入場時ドリンク代 ¥600 別途)/ 当日 ¥2,500
紙チケットの発行はなく、当日会場受付で「MELONARRATEを見に来た〇〇です」とお伝えいただき、前売料金を精算するシステムです。
普段は太平洋を挟んで音を重ねている5人が、この日だけ新宿のステージへ一堂に会します。本記事で紹介する「遠隔同期システム」を経て仕上がった生アンサンブルを、ぜひ現場で体感してください。
MELONARRATEは遠隔バンドです。メンバー5人の拠点はロサンゼルス、関西、首都圏と完全にバラバラ。そんな私たちが10月10日の初ライブに向けて直面した最大の壁が、「どうやってリハーサルを行うか」でした。
生演奏のツインリードギターに加え、Riddle of the Chimaeraのkiyurute氏による緻密な鍵盤アレンジを同期音源として流すため、ライブ用にアンサンブルを再構築する必要があります。しかし、全員が同じスタジオに集まることはできません。
「全員で音を合わせながら、リアルタイムに議論できる環境はないか」
試行錯誤の末に構築したハイブリッド構成と、実用に至るまでのトラブルシューティングを書き残します。
首都圏の3人(ドラム、ベース、ギター)が東京のリハスタに入り、関西在住のボーカル(Eiko)と、ヤマハが無料で提供している「SYNCROOM」を繋いで音を合わせる。
ロサンゼルス在住のギター(Satoshi)へ、1のリハスタ演奏音源をリアルタイム配信で届ける。
東京・関西・LAの3拠点を「Discord」のビデオチャットで常時接続し、リアルタイムに顔を合わせながらアレンジに関する議論を行う。
1の「東京↔️関西」が双方向の同時セッションであるのに対し、2は「日本➡️北米」の一方通行です。本当は3拠点の演奏を双方向で同時接続したいところですが、現在SYNCROOMが正式対応しているのは日本と韓国間のみ。2026年9月現在、太平洋を越えてバンド演奏が成立するレベルの「超低遅延かつ高音質」を双方向で実現できるツールは見当たりませんでした。そのため、日本側をホスト音源とし、LA側はその音をモニタリングしながら合わせてもらう「マスター・スレイブ方式」を採用しています。
そして、この音の連携を支える重要な土台が3のDiscordです。楽器やオケの音は低遅延・高音質の専用回線でやり取りしつつ、会話や表情、身振り手振りはDiscordのビデオ通話でカバーします。「今のギターのフレーズ、ライブではこう変えた方が映えない?」「テンポのキープ感はどう?」といった細かなニュアンスも、スタジオに全員が揃っているのと変わらないテンポ感でディスカッションできるようになりました。

それにしても、このSYNCROOMが無料ツールだという事実には驚かされます。このような革新的サービスを音楽を愛する人々に無料で開放してくれているヤマハさんには、心から敬意を表したいです。単に楽器や音響機器を製造・販売するだけでなく、「音楽文化そのものの底上げにコミットする」という強固な企業哲学を感じます。
とはいえ、SYNCROOMの実戦投入にはいくつかの落とし穴があり、私のようなIT音痴の人間にとっては、実用に耐えうる環境を構築するまで少なからずハードルがありました。本稿では備忘録を兼ねて、私たちが直面したトラブルと解決のためのルーティングを書き残しておきます。同じように遠隔リハーサルや同期演奏の構築に悩む方の参考になれば幸いです。
※今回は「首都圏リハスタと関西ボーカルを繋ぐSYNCROOM構築編」に絞って記載します。LAへの音声配信構築については、さらに長くなりますので次回以降にお届けします。
1. 「VSTモード」の幻惑
バンドで同期演奏を行うためのオケやクリックの送出元はMacのDAW(Logic Pro)です。したがって、SYNCROOMのオーディオ設定は「Core Audio」ではなく「VSTモード」を選択します。DAWのトラックにSYNCROOMプラグインをインサートして連携させるイメージです。
実は、ここが最初の躓きポイントでした。「VST?LogicってAU(Audio Units)プラグインしか読めないはずでは……?AUモードはどこ?」と混乱してしまったのです。
結論から言うと、Logicユーザーも迷わずこの「VSTモード」を使ってください。SYNCROOMをインストールするとAUプラグインも一緒に組み込まれるためLogic上で普通に読み込めますが、SYNCROOMアプリ本体側の設定項目名が「VSTモード」という表記で共通化されているだけです。
2. SYNCROOMを立ち上げる順番
「なんだ、単なる呼び方の問題か」と安心し、先にSYNCROOMアプリを起動してログイン・入室したあと、Logicのマスタートラックにプラグインを挿したところ……全く反応しません。ここで早くも心が折れかけました。
調べてみると、DAW連携(VSTモード)で使用する場合、「事前に単体でSYNCROOMアプリを起動してはいけない」という鉄則がありました。DAWのトラックにプラグインをインサートすると、バックグラウンドから自動的にSYNCROOMアプリが連動して立ち上がります。アプリはそのタイミングでログイン・入室してください。
3. サンプリングレートの不一致
無事にSYNCROOM経由で繋がり、いざオケを再生すると、音がブチブチと途切れてしまいには再生がストップ。原因は関連するハードウェアとソフトウェア間におけるサンプリングレートの不一致でした。DAWプロジェクト、SYNCROOM、オーディオインターフェースの全設定を、必ず同一のサンプリングレート(48kHz推奨)に統一しましょう。
4. 不安定なときは迷わず再起動
サンプリングレートを揃えていても、長時間の通信や回線状況によってノイズや急な遅延増大が発生することがあります。違和感を覚えたら、迷わず一度SYNCROOMを終了して再起動するのが最も確実な復帰策です。
5. 有線LANの確保という壁
無線Wi-Fiはジッターや遅延が激しいため、ヤマハ公式でも有線LANの使用が強く推奨されています。しかし、「爆音が出せるリハーサルスタジオ or 歌が歌えるスペース」かつ「専有できる高速有線LANポートが部屋にある施設」は決して多くありません。この条件を満たす拠点を探し出す作業だけでも、すくなからぬ労力を要しました。
6. DAW(Logic Pro)のルーティング設計
ここが最も頭を悩ませた本稿の核心部分です。
6-① クリックの分離送出
オケを使わず、クリックに合わせる必要もない一般的なセッションであれば、DAWのステレオマスタートラック(Stereo Out)に直接SYNCROOMプラグインを挿すだけでシンプルに完結します。
しかし、同期演奏を行う場合はそうはいきません。MELONARRATEにおいてクリック音をモニターするのはドラムとベースのリズム隊のみです。関西のボーカル(SYNCROOM)やスタジオの外音スピーカーへのクリック漏れを防ぐ必要があるため、以下のようなルーティングの工夫を行いました。
まず、SYNCROOMプラグインはマスタートラックではなく、独立して立ち上げたステレオの「AUXトラック」にインサートします(※モノラルトラックではプラグインが認識されないため、必ずステレオで作成します)。その上で、オケトラックやスタジオで演奏する生楽器のトラックから「Bus 1」センドを使い、このSYNCROOM用AUXトラックに必要な音だけを集約して送り込みます。
一方、クリックトラックはこのAUXへは一切送らず、ステレオアウト(Output 1-2)とも切り離して、独立した「Output 3-4」から出力します。これをオーディオインターフェース兼デジタルミキサー(YAMAHA MGX)の専用チャンネルへと送り込むことで、クリック音を関西や外音へ漏らすことなく、リズム隊のイヤモニだけにピンポイントで届けることができます。
6-② スタジオモニターと生楽器のループバック防止
東京のリハスタでは、LogicのStereo Outから送出されるオケ音源と、SYNCROOMを経由して返ってくるEikoの歌声を、スタジオのモニタースピーカーとリズム隊のイヤモニ双方へ返します。スタジオモニターから声を鳴らすのは、ギタリストの廣田がオケとボーカルをモニタリングできるようにするためです。リズム隊も生音の迫力を直接聴くため、イヤモニは片耳装着スタイルを採っています。
ここで極めて重要なのが、リハスタの生楽器(ドラムマイクやギター、ベース)のLogicトラック出力を、すべて「No Out」に設定することです。
もしこれらを通常の「Stereo Out」にしてしまうと、DAWを経由した生演奏の音がスタジオモニターから遅れて鳴り響き、それをマイクが再び拾って無限ループと強烈なハウリングを引き起こします。「No Out」にしつつ「Bus 1センド」のみを生かしておくことで、「東京のスピーカーからは自分の生音を出さず、関西のEikoだけに演奏音を届ける」という完全なアイソレーションが完成します。
※なお、Logic上で立ち上げた各生楽器トラックは、インプットモニタリング(Iボタン)または録音待機(Rボタン)をオンにしておかないと音声信号がBusへ流れませんのでご注意ください。
6-③Logic Pro ルーティングマトリックス

言葉で説明すると複雑に見えますが、Logic内部の信号の行き先を整理したマトリックス表が上図です。要点は、「オケはStereo OutとBus 1の両方に流す」「クリックはOutput 3-4へ逃がす」「東京の生楽器はNo OutにしてBus 1だけに流す」という3点に集約されます。
7. SYNCROOM側のモニター設定
東京側で鳴らしている自分たちの楽器やオケは、手元のミキサーからリアルタイム(遅延ゼロ)でモニタリングしています。
もしSYNCROOM側でも「自分の音」をモニターしてしまうと、サーバーを往復して十数ミリ秒遅れて返ってきた自分の音がダブって聴こえ、強烈なディレイがかかったような状態になり演奏どころではなくなります。
SYNCROOM画面上の「自身のマイク・モニター音」スライダーはゼロにし、完全にミュートしてください。
※注記:
下記赤囲みのスライダーをゼロにすることでSYNCROOM内の自分の演奏音が聞こえなくなるはずなのですが、実際には関西を経由したと思われる自分たちの演奏音が、僅かに混じって東京に帰ってきます。原因を調べているところですが、もし何か要因をご存じの方がいらっしゃったらアドバイス頂けると大変助かります。

8. オーディオインターフェース兼ミキサーの選定
当初は超小型で可搬性に優れ、単体マルチトラック録音も可能なZoom LiveTrak L6maxをオーディオインターフェース兼ミキサーとして導入していました。このL6 Maxは上記の複雑なルーティングを実現させるだけではありません。全員が一堂に会するSYNCROOM不要の現場であれば、microSDカードからのマルチ再生を活用することで、オケ同期演奏におけるPCトラブル時のバックアップ機としても使えるため、極めて高いコストパフォーマンスを誇ります。
しかし、フルバンドが爆音で鳴り響くリハスタ環境において、楽器マイクのゲイン確保やマイクプリアンプのヘッドルームをシビアに突き詰めた結果、据え置き機であるYAMAHA MGXへ移行することにしました。(ライブ本番は、生楽器はライブハウスのPA卓に接続されるため、MGXではなくL6maxを使用する予定です)
8-①YAMAHA MGX16 インプット構成
CH 1〜3: ドラムマイク(Kick / Snare / Monaural Overhead)
CH 4: ギターアンプ収音マイク
CH 5: ベースライン入力
CH 6: コーラスマイク
CH 9/10(USB 1/2): Logicからのオケ+SYNCROOM経由のボーカル
CH 11/12(USB 3/4): Logicからのクリック音
8-②YAMAHA MGXアウトプット構成
Omni Out 1/2: リハスタのメイン卓へ(オケ+関西ボーカルを外音スピーカーから再生)
Stereo Out: リズム隊用Xviveワイヤレス送信機へ接続
尚、ドラマーが手元のミニミキサーを使用してオケとクリックバランスを調整できるようにするためには、MGXのOmni Out 3からクリック音を、Omni Out 4/5から「生音+オケ」を送出し、ワイヤレス送信機はミニミキサーのヘッドホン端子に挿します。
ここまで組み上げることで、何百キロも離れた関西のボーカルと東京のリハスタが、あたかも同じ部屋にいるかのようなレスポンスでセッションできる環境が整いました。関西にいる彼女の歌声が、東京のリハスタのモニターから遅延もなく綺麗に響いたとき、東京の3人はとても感動しました。遠隔バンドが初めて繋がった瞬間です。
しかし、私たちの挑戦はここからが本番です。この東京と関西のアンサンブルの音と映像を、さらに海の向こうのロサンゼルスへリアルタイムに届けるという、もうひとつの大きな関門が待ち受けていました。その奮闘の模様は、次回詳しくお伝えします。
MELONARRATE Bass: Aosigray
Achieving Synchronized Band Performances Remotely #1 — A SYNCROOM × Logic Pro Battle Log
[Information]
Details have been finalized for the debut live show of MELONARRATE, a remote rock band with members based in Tokyo, Kansai, and Los Angeles.
Date: Saturday, October 10, 2026
Venue: Shinjuku LiveFreak
MELONARRATE Stage Time: 19:50~
The five of us, who normally layer our sounds across the Pacific Ocean, will unite on stage in Shinjuku for this one night. We invite you to come and experience firsthand the raw ensemble forged through the "remote sync system" detailed in this article.
MELONARRATE is a remote band. Our five members are completely scattered across Los Angeles, the Kansai region, and the Greater Tokyo area. Gearing up for our debut live performance on October 10, the single greatest hurdle we faced was simple: "How do we rehearse?"
Along with our live twin lead guitars, our stage set incorporates backing tracks featuring the intricate keyboard arrangements crafted by kiyurute of Riddle of the Chimaera, which required us to reconstruct the ensemble specifically for a live setting. However, gathering everyone into a single rehearsal studio was physically impossible.
"Is there a way for all of us to play together and discuss arrangements in real time?"
This article documents the hybrid setup we engineered after extensive trial and error, along with the troubleshooting steps we took to make it fully production-ready.
Normally, a band would simply gather in a rehearsal studio, jam together, and hash out ideas in person. For us, that was not an option. "Is there a way for all of us to play together and discuss arrangements in real time?" After extensive trial and error, we arrived at the following hybrid rehearsal setup:
The three Tokyo-based members (drums, bass, and guitar) enter a rehearsal studio in Tokyo and jam together with our Kansai-based vocalist (Eiko) via Yamaha’s free remote-session app, "SYNCROOM."
We stream the live rehearsal audio from Step 1 in real time to our guitarist in Los Angeles (Satoshi).
We keep all three locations—Tokyo, Kansai, and LA—constantly connected via Discord video chat, allowing us to discuss arrangements face-to-face in real time.
While Step 1 (Tokyo ↔ Kansai) is a bidirectional, simultaneous session, Step 2 (Japan ➔ North America) is strictly a one-way transmission. Ideally, we would have loved a bidirectional simultaneous session across all three points. However, as of September 2026, SYNCROOM officially supports cross-border connections only between Japan and South Korea. There was simply no viable tool available capable of achieving the ultra-low latency and pristine audio quality required for real-time band performance across the Pacific Ocean. Therefore, we adopted a "master-slave" architecture: the Japan side acts as the master audio host, while LA monitors the feed and plays along.
The essential glue holding this audio chain together is Step 3: Discord. While musical instruments and backing tracks are transmitted over dedicated low-latency, high-fidelity lines, everyday conversation, facial expressions, and body language are handled through Discord video. This allows us to discuss fine nuances—like "Wouldn't this guitar riff pop more live if we tweaked it like this?" or "How's the pocket and tempo feel?"—with the exact same immediacy as if we were all standing in the same room.

Still, it is mind-blowing that SYNCROOM is completely free to use. I have the utmost respect for Yamaha for offering such an innovative service to the music community free of charge. Beyond simply manufacturing and selling instruments and audio gear, one can clearly feel Yamaha's steadfast corporate philosophy: a true commitment to elevating musical culture as a whole.
That said, deploying SYNCROOM in a serious band environment comes with a few traps. For someone like me who is far from a tech wizard, building a truly production-ready setup presented quite a learning curve. As a reference for myself and anyone else struggling with remote band rehearsals and backing-track synchronization, I have documented the obstacles we encountered and the routing solutions we devised.
(Note: This article focuses specifically on setting up SYNCROOM between the Tokyo rehearsal studio and our Kansai vocalist. The setup for audio streaming to LA will be covered in a subsequent post.)
1. The "VST Mode" Confusion
To play along with backing tracks and a click track, our audio source is a Mac running Logic Pro. Therefore, in SYNCROOM’s audio settings, you must select "VST Mode" instead of "Core Audio." Essentially, you insert the SYNCROOM plugin directly onto a DAW track.
This was our very first stumbling block. "VST? Doesn't Logic only support AU (Audio Units) plugins? Where on earth is the 'AU Mode'?" I was thoroughly confused.
Long story short: Logic users should select "VST Mode" without hesitation. When you install SYNCROOM, the AU plugin component is installed alongside it, so Logic loads it without issues. Yamaha simply uses "VST Mode" as the universal label inside the SYNCROOM application interface.
2. The Strict Launch Sequence
Relieved that it was merely a labeling quirk, I initially launched the SYNCROOM standalone app, logged in, entered a room, and then inserted the plugin onto Logic’s stereo master track... and nothing happened. Not a single sound. My spirits almost broke right there.
As it turns out, when using SYNCROOM inside a DAW (VST Mode), there is an ironclad rule: you must never launch the standalone SYNCROOM app beforehand. When you insert the plugin onto a DAW track, the SYNCROOM application launches automatically in the background. That is the exact moment you should log in and join the room.
3. Sampling Rate Mismatch
Once connected through SYNCROOM, we hit play on our backing track, only for the audio to stutter, crackle, and grind to a complete halt. The culprit was a sampling rate mismatch across the connected hardware and software. Make sure to unify the sample rates across your DAW project, SYNCROOM, and your audio interface to the exact same setting (48 kHz is strongly recommended).
4. When in Doubt, Restart
Even with matching sample rates, long sessions or fluctuating network conditions can occasionally introduce digital noise or sudden latency spikes. If something feels off, closing SYNCROOM and relaunching it is by far the most reliable fix.
5. The Hardwired LAN Hurdle
Because Wi-Fi suffers from jitter and packet loss, Yamaha strongly advises using a hardwired Ethernet connection. However, finding a rehearsal space that meets both criteria—"a facility where you can play at full stage volume / belt out vocals" and "a dedicated room equipped with a high-speed wired LAN port"—is surprisingly difficult. Scouring locations that met these requirements took a substantial amount of effort.
6. DAW (Logic Pro) Routing Architecture
This was the most challenging puzzle of all.
6-① Isolating and Routing the Click Track
In a casual jam session without backing tracks or a click, inserting the SYNCROOM plugin directly onto the DAW’s Stereo Master track (Stereo Out) works just fine.
However, when performing with backing sequences, that won't fly. In MELONARRATE, only the rhythm section (drums and bass) monitors the click track. To prevent the click from leaking to our vocalist in Kansai (via SYNCROOM) or through the rehearsal studio PA speakers, we devised the following routing:
First, instead of the Master track, we insert the SYNCROOM plugin onto a dedicated stereo Aux track (note: create a stereo Aux track, as the plugin will not function on a mono track). Then, using Bus 1 sends from the backing track and the live instrument tracks inside the studio, we route only the necessary audio elements into this SYNCROOM Aux track.
Meanwhile, the click track is never sent to Bus 1, and its output is unlinked from the main Stereo Out (Output 1-2).Instead, it is routed to dedicated outputs: Output 3-4. By feeding these separate outputs into dedicated channels on our audio interface/digital mixer (Yamaha MGX), we deliver the click pinpoint to the rhythm section’s IEMs without spilling into Kansai or the room's main PA.
6-② Preventing Studio Monitor and Live Instrument Feedback Loops
Inside the Tokyo studio, the backing tracks sent from Logic's Stereo Out and Eiko’s incoming vocals from SYNCROOM are fed into both the studio monitor speakers and the rhythm section's IEMs. We run the vocals through the studio speakers so our guitarist, Hirota, can clearly monitor the backing track and vocals. Meanwhile, the rhythm section wears only one earpiece to balance the IEM signal with the acoustic impact of the live drums and amps.
At the rehearsal studio in Tokyo, both the backing tracks routed from Logic’s Stereo Out and Eiko’s vocals returned via SYNCROOM are fed to both the studio monitor speakers and the rhythm section’s in-ear monitors (IEMs).
Running the vocals through the studio monitors allows our guitarist, Hirota, to monitor both the backing tracks and the vocals. Meanwhile, the rhythm section wears their IEMs in only one ear so they can also directly hear the raw power and energy of the live sound.
The crucial key here is setting the output of all live instrument tracks in Logic (drum mics, guitar, bass) to "No Out."
If you leave these set to the standard "Stereo Out," the live performance audio running through the DAW will output through the studio speakers with slight latency, get picked up again by the microphones, and cause an immediate infinite feedback loop. By keeping them set to "No Out" while leaving only the "Bus 1 send" active, we achieve complete isolation: our live sound is muted from the Tokyo speakers, while cleanly reaching Eiko in Kansai.
(Note: Ensure that Input Monitoring [I button] or Record Enable [R button] is turned on for all live instrument tracks in Logic, or audio will not flow through the Bus sends.)
6-③ Logic Pro Routing Matrix

While it sounds complicated in words, the matrix above illustrates the internal signal routing in Logic. It all boils down to three core principles:
Route backing tracks to both Stereo Out and Bus 1.
Route the click strictly to Output 3-4.
Set Tokyo live instruments to No Out, routing them exclusively to Bus 1.
7. SYNCROOM Monitor Settings
We monitor our own instruments and backing tracks in Tokyo directly through our hardware mixer in real time (zero latency).
If you monitor your own sound inside SYNCROOM as well, your audio will travel to the server and back, returning with a dozen-plus milliseconds of delay. This creates an intense slapback echo that makes playing impossible. Be sure to slide the "Own Mic/Monitor Sound" fader in SYNCROOM all the way to zero to mute it completely.
(Note: Lowering the red-boxed fader to zero should completely silence your own performance sound inside SYNCROOM. However, in our setup, a faint trace of our own playing—seemingly looped back from Kansai—still returns to Tokyo. We are currently diagnosing the cause, so if anyone has insight into this, advice would be greatly appreciated!)

8. Selecting Our Audio Interface / Digital Mixer
Initially, we deployed the ultra-compact, highly portable Zoom LiveTrak L6 Max, which supports standalone multitrack recording, as our audio interface and mixer. The L6 Max is capable of handling complex routing and offers exceptional value: for gigs where everyone is in the same room and SYNCROOM is not needed, it can serve as a dependable hardware backup for backing tracks via microSD playback if the DAW laptop ever crashes.
However, in a rehearsal studio with a full band blasting at high volume, we needed greater mic pre headroom, substantial gain margin, and multiple dedicated auxiliary routing paths. Consequently, we transitioned to a desktop digital console: the Yamaha MGX16. (Note: For the actual live gig, live instruments will plug directly into the venue's FOH console, so we plan to use the compact L6 Max on stage rather than the MGX.)
8-① Yamaha MGX16 Input Configuration
CH 1–3: Drum mics (Kick / Snare / Monaural Overhead)
CH 4: Guitar amp mic
CH 5: Bass direct line input
CH 9/10 (USB 1/2): Backing tracks from Logic + vocals via SYNCROOM
CH 11/12 (USB 3/4): Click track from Logic
8-② Yamaha MGX16 Output Configuration
Omni Out 1/2: To the rehearsal studio main console (playing backing tracks + Kansai vocals through the room PA)
Stereo Out: Connected to the Xvive wireless transmitter for the rhythm section's IEMs
If we allow our drummer to independently adjust the balance between the backing tracks and the click on a personal sub-mixer, we would send the click from Omni Out 3 and the "live sound + backing tracks" mix from Omni Out 4/5, connecting the wireless transmitter to the sub-mixer's headphone jack.
With this architecture in place, our vocalist in Kansai—hundreds of kilometers away—and our rhythm section in Tokyo can jam with the instantaneous response of playing in the exact same room. When her vocals, sent all the way from Kansai, resonated cleanly through the monitors in the Tokyo studio without any latency, the three of us in Tokyo were deeply moved. It was the very moment our remote band truly connected for the first time.
However, this was only half the battle. Our next major hurdle was streaming this combined Tokyo–Kansai ensemble audio and video to Los Angeles in real time across the Pacific. I will share the details of that struggle in our next post!
MELONARRATE Bass: Aosigray